EN 
IT 
ES 
DE 
FR 
PT 
| 中文名 | 英文名 | 挡板 | stop plate | |
|---|---|---|---|---|
| 浇注系统 | feed system | 方铁 | spacer block | |
| 进料位置 | gate location | 模具底板 | bottom clamp plate | |
| 浇口 | gate | 定模板 | A plate | |
| 浇口形式 | gate type | 动模板 | B plate | |
| 侧浇口 | edge gate | 推板 | stripper plate/ejector plate | |
| 点浇口 | pin-point gate | 推杆底板 | ejector support plate | |
| 直接浇口 | direct gate | 推杆固定板 | ejector retainer plate | |
| 环形浇口 | ring gate | 导板 | guide plate | |
| 盘形浇口 | disk gate | 滑板 | slide plate | |
| 潜伏浇口 | submaring gate | 隔热板 | insulated plate | |
| 扇形浇口 | fan gate | 定模型腔 | cavity | |
| 护耳浇口 | tab gate | 动模型芯 | core | |
| 浇口大小 | gate size | 活动型芯 | movable core | |
| 转浇口 | switching gate | 定模镶件 | cavity insert | |
| 浇注口直径 | sprue diameter | 动模镶件 | core insert | |
| 流道 | runner | 镶针 | core pin | |
| 热流道 | hot runner | 螺纹型芯 | threaded core | |
| 冷流道 | cold runner | 导柱 | leader pin/guide pin | |
| 圆形流道 | round runner | 导套 | bushing/guide bushing | |
| 梯形流道 | trapezoidal runner | 推杆板导套 | Ejector guide bushing | |
| 模流分析 | mold flow analysis | 推杆板导柱 | Ejector guide pin | |
| 流道平衡 | runner balance | 热流道导套 | Support bushing | |
| 热射嘴 | hot sprue | 热流道导柱 | Support pin | |
| 热流道板 | hot manifold | 斜导柱 | angle pin | |
| 发热管 | cartridge heater | 弯销 | dog-leg cam | |
| 探针 | thermocouples | 滑块 | slide | |
| 插头 | connector plug | 斜滑块 | angled-lift splits | |
| 插座 | connector socket | 斜顶 | angle from pin | |
| 密封圈 | Oring/seal ring | 楔紧块 | wedge | |
| 冷却水 | water line | 耐磨板 | wedge wear plate | |
| 喉塞 | pipe plug | 压条（块） | plate | |
| 喉管 | tube | 限位钉 | stop pin | |
| 塑料管 | plastic tube | 斜顶（斜推杆） | angle ejector rod | |
| 隔片 | buffle | |||
| 模具零件 | mold components | |||
| 三板模 | three-plate mold | 中文名 | 英文名 | |
| 二板模 | two-plate mold | 撑柱（头） | support pillar | |
| 双层模 | two-plate mould | 拉斜杆 | sprue puller | |
| 三层模 | three-plate mould | 先复位机构 | early return | |
| 模架（坯） | mold base | 先复位杆 | early return bar | |
| 定位圈 | locating ring | 弹簧柱 | spring rod | |
| 浇口套 | sprue bushing | 弹簧 | die spring | |
| 固定板 | retainer plate | 定位销 | dowel pin | |
| 托板 | support plate | 内模管位 | core/cavity inter-lock | |
| 垫板/支承板 | backing plate | 推杆 | ejector pin | |
| 定位板 | locating plate | 有托推杆 | Stepped Ejector Pin | |
| 推管 | ejector sleeve | 排气 | Venting | |
| 推管型芯 | ejector pin | 填充剂 | filler | |
| 推块 | ejector pad | 阻燃剂 | flame retardant | |
| 扁推杆 | Ejector blade | 聚合物 | polymer | |
| 推块 | push bar | 树脂 | resin | |
| 锁扣 | latch | 润滑剂 | lubricant | |
| 活动臂 | lever arm | 黏结剂 | adhesive | |
| 复位杆 | Return pin | 催化剂 | accelerator | |
| 撬模槽 | ply bar score | 添加剂 | additive | |
| 斜度锁 | taper lock | 抗氧化剂 | antioxidant | |
| 直身锁（边锁） | side lock | 抗静电剂 | antigtatic agent | |
| 锁模块 | lock plate | 着色剂 | colorant | |
| 扣基 | parting lock set | 稳定剂 | stabilizer | |
| 螺钉 | screw | 增塑剂 | plasticizer | |
| 尼龙塞 | nylon latch lock | |||
| 气阀 | valves | |||
| 分型面排气槽 | parting line venting | |||
| 老化 | aging | |||
| 光泽 | gloss | |||
| 双色注塑 | double-shot moulding | |||
| 线切割 | wire cut | |||
| 火花电蚀 | EDM | |||
| 铜公（电极） | copper electrode | |||
| 数控加工 | CNC | |||
| 雕字 | engrave | |||
| 基准 | datum | |||
| 注射压力 | injection pressure | |||
| 成型压力 | moulding pressure | |||
| 锁模力 | clamping force | |||
| 开模力 | mould opening force | |||
| 中文名 | 英文名 | |||
| 抽芯力 | core-pulling | |||
| 抽芯距 | core-pulling distance | |||
| 抛光 | buffing | |||
| 飞边 | flash/buns | |||
| 流痕 | ripples | |||
| 填充不足 | short shot | |||
| 收缩凹痕 | sink marks | |||
| 熔接痕 | weld line | |||
| 银纹 | spray marks | |||
| 拉丝 | string | |||
| 顶白 | stress marks | |||
| 气纹 | vent marks | |||
| 弯曲 | warpage | |||
| 公差 | tolerance | |||
| 注塑周期 | moulding cycle | |||
| 分型线 | mould parting line |
-
Address: Mold city Huangyan,CN 318020
-
Phone: + 86 159-6865-2523
-
Email: sales@plasticmoulds.net